Lamellar pack Quattrini engine crankcase "C1" for Vespa 50/90/125 Primavera ET3 / PK
77x77x40 mm
incl. gaskets
4 valves without stop
Vespa 50/90/125 Primavera ET3 / PK
Related articles
Vespa 50/90/125
High-speed bearing (up to 18000 rpm) produced by SKF ITALIA, used on Pinasco and Quattrini engine casings.
Needle roller bearing pre-selector rod gearbox (10x14x10mm) for Vespa 50/125 PK XL2/FL
Vespa 50 PK FL V5N1T
Vespa 50 PK HP V5N2T
Vespa 50 PK XL2/ Elestart V5X3T
Vespa 125 PK XL2 VMX6T
Vespa 125 N (FL) VMX7T
Gear selector rod oil seal (10x18x4mm) for Vespa 50/125 PK XL2/FL
Vespa 50 PK FL V5N1T
Vespa 50 PK HP V5N2T
Vespa 50 PK XL2/ Elestart V5X3T
Vespa 125 PK XL2 VMX6T
Vespa 125 N (FL) VMX7T
"Racing" crankshaft Pinasco full mass crankcases for Vespa 50/90/125 Primavera-ET3-PK
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Cone 20 mm / Cone 20 mm
Stroke 51 connecting rod 97, shoulders 88mm, complete with screw-in inserts to increase its weight which without them weighs 192 gr.
Bronze inserts-->104gr, iron-->95gr, aluminum-->34gr
Quattrini high-speed oil seal kit (24x35x7) for Vespa 50/90/125 Primavera-ET3-PK
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Compatible with Carter Quattrini and Pinasco
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Compatible with Carter Pinasco and Pinasco crankshaft code 26081951
Pinasco Factory full circle crankshaft stroke 54 rod 110 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Specific for Master Pinasco casings with tungsten inserts and specific keying for Pinasco sprockets. Racing imbalance, high performance, and remarkable resistance to stress are the characteristics of this product. With the Pinasco keying system, it is possible to remove the sprocket from the crankshaft without having to disassemble the clutch, reed valve intake.
Bearings--->25x52x15 (C4).
Fabbri Racing full circle crankshaft (87) stroke 51 connecting rod 97 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Carter Piaggio
Oil seals-->27x47x6/20x32x7
Tameni crankshaft cone 20 full shoulders (87) stroke 54 reinforced rod 97 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Vespa ET3 Primavera 125, PK, XL 50/125
Advanced Crankshaft Parmakit EVO - Vespa ET3 - stroke 51 rod 97 cone 20
Vespa ET3 Primavera 125, PK, XL 50/125.
Vespa ET3 Primavera 125, PK, XL 50/125.
Race: 51
Biella: 105
Fabbri Racing full circle crankshaft stroke 53 connecting rod 105 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Specific for Master Pinasco crankcase
Bearings--->25x52x15 (C4) Oil seals-->24x35x7/20x35x7
Shoulders--> 86mm Weight--> 2.2kg
Parmakit full circle crankshaft (83) stroke 51 connecting rod 97 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Carter Piaggio
CONO 20
Tameni crankshaft cone 19 full shoulders (87) stroke 54 rod 97 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Tameni crankshaft cone 19 full shoulders (87) stroke 54 reinforced rod 97 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Tameni crankshaft cone 20 full shoulders (87) stroke 54 rod 97 for Vespa 125 Primavera ET3/PK/ETS
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Polini crankshaft advanced cone 19 connecting rod 97 stroke 51 for Vespa 125 Primavera ET3
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Polini crankshaft advanced cone 20 rod 97 stroke 51 for Vespa 125 Primavera ET3-PK
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S-XL-N-HP
Carter motore Quattrini "C1" lamellare per Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
Carter per Vespa Special, Et3 e PK interamente fusi e lavorati in Italia.
Sono rinforzati nello spessore in ogni sua parte, realizzati in conchiglia con materiale Galsi9 temprato e assemblaggio con 13 viti brugola da 6mm.
Dal lato volano sono lavorati in modo da ospitare anche l'accensione Vespatronik e nella parte superiore sono predisposti per il montaggio di marmitte che girano dietro all'ammortizzatore (tipo M3XC, Tipo R o
simili).
In origine è chiuso di fusione, basterà aprirlo per montare cilindri senza aspirazione.
Il braccio di supporto è molto più robusto dell'originale, conformato in
modo da permettere l'uso di una gomma 3,50/10.
Dotati di supporto per la pompa dell'acqua che prende il movimento dal
quadruplo del cambio (terza marcia).
Il basamento largo e spesso è fatto per alloggiare vari tipi di cilindri
della serie M, R o di altre marche, senza riporti di saldature.
All'interno il carte pompa è lavorato per il montaggio del suo albero a
spalle piene dedicato, con asse di accoppiamento lungo 48mm, cuscinetti
di banco (codice 6304/c4) da 20-52-15mm e paraoli (smontabili
dall'esterno) da 20-35-7mm.
E' possibile montare ricambi originali (perno ruota, cambio, quadruplo,
rapporti, frizioni,…).
QUESTI COMPONENTI SONO DESTINATI SOLO AD USO AGONISTICO-SPORTIVO.
Albero motore Quattrini 8348 carter motore "C1" per Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
Spalle piene Ø85mm , corsa 51mm, biella 102mm, lunghezza asse 48mm.
Da montare con due cuscinetti 25x52x15mm e due paraoli 24x35x7mm. opzionali da acquistare eparatamente
Vespa 50/90/125 Primavera ET3 / PK
Aluminum casting
Intake manifold with 2 holes
Flywheel side bearing seat 20mm
TÜV certified
Crankshaft Quattrini A-8736 full circle ⌀ 87 cone 20 stroke 51 rod 97 for Vespa 50/90/125 Primavera ET3 / PK-Ape 50
Vespa 50/90/125 Primavera ET3 / PK
Full shoulders Ø87mm, stroke 51mm, connecting rod 97mm, shaft length 48mm.
Pin 15 mm
Parmakit Crankshaft - Vespa ET3 - 97mm W-Force connecting rod - cone 20 for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
- Cone 20
- Shoulders 87
- Connecting rod 97
- Stroke 51
- Wrist pin 15
- Silver-plated needle cage
Crankshaft Parmakit - Vespa ET3 - W-FORCE stroke 56mm rod 105 - cone 20 - pin 20 for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
- Cone 20
- Shoulders 87
- Connecting rod 105
- Stroke 56
Parmakit Racing Crankshaft - Full circle 87mm cone 19 - Vespa ET3-Ape 50
VESPA: ET3 - PRIMAVERA 125 - PK - PK XL 50/125
Full shoulders 87mm
Con: 19mm
Connecting rod: 97mm
Stroke: 51mm
Parmakit Racing Crankshaft - Full webs 87mm cone 20 - Vespa ET3 for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
VESPA: ET3 - PRIMAVERA 125 - PK - PK XL 50/125
Full shoulders 87mm
Cone: 20mm
Connecting rod: 97mm
Stroke: 51mm
Parmakit Crankshaft - 83mm Shoulder cone19 - for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
Vespa ET3 Primavera 125, PK, XL 50/125
shoulders: 83
cone: 19
Parmakit Crankshaft - 105 Rod Cone 20 - ET3 125 for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
Vespa ET3 Primavera 125, PK, XL 50/125
Advanced Crankshaft Parmakit - Cone 19 - for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
Vespa ET3 Primavera 125, PK, XL, ETS 125.
Advanced Crankshaft Parmakit - Cone 20 - for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
Vespa ET3 Primavera 125, PK, XL, ETS 125.
Vespa 50/90/125 Primavera ET3 / PK
- Gravity cast aluminum housing
- Bearing seat 20x47x14
- Intake: 3-hole manifold attachment
- Crankshaft shoulder seat clutch side 87
- Crankshaft shoulder seat flywheel side 83
Vespa 50/90/125 Primavera ET3 / PK
- Gravity-cast aluminum casing
- Bearing seat 20x47x14
- Intake: 3-hole manifold connection
- Crankshaft side shoulder seat clutch side 88mm
- Crankshaft side shoulder seat flywheel side 88mm
- Worked transfer ports
Adaptable to thermal groups
- SP09
- W-FORCE RED DEVIL
- READY TO RACE
- SIXTY SIX
BGM Pro racing full circle crankshaft ⌀ 88 cone 20 stroke 54 rod 105 for Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
Full shoulders Ø88mm, stroke 54mm, connecting rod 105mm, shaft length 48mm.
Wrist pin 15 mm
flywheel side bearing seat diameter: 25mm
flywheel side oil seal seat diameter: 24mm
Corteco oil seal kit (24x35x7) for Vespa 50/90/125 Primavera-ET3-PK
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL/N/HP
Compatible with Carter Quattrini and Pinasco
VMC engine casing "X1" model ROTARY VALVE for Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
Carter VMC X1 for Vespa Small Frame mod. ROTARY VALVE
The evolution of modifications in the Vespa world is constantly evolving, and VMC has also decided to create specific casings for Vespa small frame that can accommodate the most powerful thermal kits and larger displacements available on the market. VMC has designed and manufactured casings capable of meeting these needs and has given life to the VMC X1 Casings
The Vespa Smallframe VMC X1 Casings are made of aluminum alloy, cast in sand molds and CNC machined in Italy, and checked for dimensions with high precision instruments.
Compared to Piaggio casings and semi-standard aftermarket versions, VMC casings feature technical improvements that position them at a higher level and make them the essential base for those who want a safe product made by enthusiasts for enthusiasts.
The VMC X1 engine casings have the following technical features:
- innovative fastening system for removable gear wire rods, which, combined with our external rod gear sheaths, speeds up engine change and gear cable tension adjustment
- increased wall thickness for greater resistance to mechanical stress
- a very wide cylinder support base
Vespa 50/90/125 Primavera ET3 / PK
- increased wall thickness for greater resistance to mechanical stress
- a very wide cylinder support base and a lot of material underneath that allows for the creation of very generous transfer ports
- Bearing seat on the flywheel side with a seat diameter of 47 as on the Piaggio 50 Special and 125 Primavera ET3 versions
SIP EVO black engine casing, reinforced type for Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
3-hole manifold
Flywheel side bearing 20X47X14
SIP EVO engine casing black reinforced type for Vespa 50/90/125 Primavera ET3 / PK
Vespa 50/90/125 Primavera ET3 / PK
3-hole manifold
Flywheel side bearing 25x38x15mm (ETS/PX)
BGM PRO racing crankshaft advanced cone 19 connecting rod 97 stroke 51 for Vespa 125 Primavera ET3
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Sport Crankshaft – Rotary Valve Intake Optimization
The ideal component for those who want to upgrade to larger displacements (125cc or more) while maintaining the original ignition system.
Unlike a standard crankshaft, this model features an extended intake phase, specifically designed for tuned engines. When installing a tuning cylinder, the original crankshaft often becomes a "bottleneck": the too short intake time prevents the engine from breathing properly, causing a drastic drop in performance as soon as the revs increase.
Why choose this crankshaft:
Smooth Delivery and High Revs: Thanks to optimized phase angles, the engine maintains the smoothness of an original Piaggio at low revs, but ensures the necessary airflow to reach maximum power at high revs.
Maximum Compatibility: Perfect for those who want to increase performance without overhauling the electrical system or replacing the ignition.
Tuning Potential: The crankshaft's compliance allows for working and widening the rotary valve on the crankcase, creating the necessary volume to accommodate larger carburetors and push performance to the next level.
Mazzuchelli SUPER COMPETITION crankshaft AMT182 cone 19 connecting rod 97 stroke 51 for Vespa 125 Primavera ET3
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 50/90/125 Primavera ET3 / PK
2-hole manifold
Flywheel side bearing 20x47x14