Spare Parts Vespa 50 Sprinter V5SS2T
An exclusive selection of spare parts for Vespa 50 Sprinter (chassis V5SS2T), the rare "fast" version produced in the '70s for the foreign market. Here you will find the hard-to-find components for this collector's model: from the iconic "Sprinter" adhesive stripes for the shield and sides, to the specific thermal group that made it faster than the standard 50. Rely on our catalog for a faithful restoration of this piece of Vespa history.
EVOK clutch plate with 30mm bearing for Vespa 50-125/PV/ET3/PK/S/XL/VNA-TS/150 VBA-Super/PX80-150/PE/Lusso
Vespa 50/90/125/150/200
SparkEvo "Zero Absolute" control unit conversion from points to electronic for Vespa 50 N/L/R-Special-125 Primavera/Sprint-Super-GT/GTR/TS/Rally/SS/-PX 1st Series-Ciao-Si-Bravo-Boxer
Models with points ignition
For conversion to electronic ignition
Zero Absolute is the ultimate solution to eliminate points and condenser from your Vespa or moped!
This ignition module completely replaces the mechanical ignition system, offering a more powerful spark, a quicker response and an increase in maximum RPM.
-Completely removes points and condenser, no additional sensor needed
-No external battery required, all original components are retained (coil, stator, flywheel)
Static advance adjustment from -15° to +15° (via trimmer on the device)
-Preloaded variable advance maps
-RPM limiter activatable via switch
Oil can support - luggage rack for internal shield -MRP- Vespa Smallframe, Largeframe 10 inches - to be mounted on the thread for the front spare wheel support - right side
All models
Vespa 50/90/125/150/160/180/200
FB 36 clutch spring kit Fabbri Racing for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
For Fabbri racing clutches
Multiple gear Fabbri Racing 10-14-17-19 THIRD AND FOURTH SHORT triangle section + z=47 Vespa 50, 90, 125 ET3 Primavera, PK + spider
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The cluster 10 14 17 19 meshes with original Vespa sprockets: 58 54 50 and
dedicated fourth gear z47 Compatible with Vespa/ape50 Piaggio engine cases and
aftermarket. The smaller gap in gear shifting from second to third to fourth,
allows the engine to stay in power band reaching maximum speed
in less time. Ideal for tuned engines or track configurations.
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Dimensions: 20x47x14 mm (Flywheel side )
SKF wheel hub bearing 6204-C5 20x47x14 mm for Vespa 50/90/125/150/200
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa PK
Vespa 150 GS VS5T
Vespa 150 VB1T
Vespa 180 Rally VSD1T
Vespa PX/PE
Measurements: 20x47x14 mm
All models / Tutti i modelli
Vespa 50 V5A1T N/L/R
Vespa 50 Special
Vespa 50 PK
Prisoner intake manifold fastening M6x30 for Vespa 50/125 N-L-R/Special/PK-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
All models / Tutti i modelli
chrome
l=85 mm
Ø internal 21mm
Cone pin clip of Orto MA/UA/UB23S3 for Vespa 125 VNA/150 VB/VL/GS
Mounting and dismounting tool cross -BGM PRO- for Vespa 50 Special V5B3T/90 V9A1T-125 Primavera ET3-PK-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
The BGM PRO ball crimping tool is an intelligently designed tool. It can be used to easily and conveniently install the gear balls with the spring in the main shaft of Vespa Smallframe engines.
Easy disassembly/assembly of gear balls
The gear balls are held firmly in place
The main shaft is held by the tool - both hands free to mount the gear lever
100% made in Germany
Without this tool, assembling the gear claw is a real game of patience. How do you position and sufficiently preload the balls on both sides at the same time without the gear spring shooting them into the infinite expanse of the workshop? It's not uncommon for the balls to simply disappear and you need new ones, of course exactly on a weekend...
With the BGM PRO tool, the job is done in no time. The whole process is so enjoyable that you want to do it over and over again. Simply because it is so nice... Indispensable in every Vespa workshop.
Trolley extension for motorcycle mover (rear wheel) -BGM PRO- Vespa Smallframe/Largeframe/Wideframe V50-V90-ET3-PK-PX-T5-Rally-Sprint-GT-GTR-SS180-GL-Super-GS160-VNA-VNB-VBA-VBB-V1-V15-V30-V33
Vespa Smallframe, largeframe, wideframe
Brilliant extension for maneuvering assistance by BGM PRO for all classic
Vespa and Lambretta scooters. With the addition for the rear wheel, the
vehicle can be turned on the spot. This way, the scooter can be stored
well and safely even in the smallest corner and can be easily removed
again. All this without any effort.
Grease Gun -NORMFEST- Lever grease gun for 400g or 500g cartridges and bulk grease
Complete clutch assembly for Vespa 50/90/125 Primavera ET3-PK/S/XL-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK S/XL
Vespa 125 PK ETS VMS1T
Composed of 3 cork discs + 2 steel discs
Tool for assembling cruciform gear selector balls for Vespa 50-125/PV/ET3/PK50-125/S/XL/XL2
Vespa 50/90/125 Primavera ET3
Rivet setting tool set Ø=2mm, 3mm, 4mm, 5mm, 6mm for rivets according to DIN 660
Base plate thermal group FlowPlate - LS ENGINEERING - for Vespa 50/90/125 Primavera ET3-PK S/XL/N/HP (mounting Quattrini M1L cylinders on PIAGGIO cases without boring and matching the ports)
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK ETS
Vespa PK 50 S/XL/N/HP
Vespa 125 PK
8 mm base gasket for thermal group for Vespa 50/90/125 Primavera ET3-PK S/XL/N/HP
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK ETS
Vespa PK 50 S/XL/N/HP
Vespa 125 PK
1 mm spacer for thermal group for Vespa 50/90/125 Primavera ET3-PK S/XL/N/HP
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK ETS
Vespa PK 50 S/XL/N/HP
Vespa 125 PK
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Kit composed of: 2 Adjustable Shock Absorbers 100% Made in Italy (Red body and red spring), Bump stops, rear silent block, rear shock absorber bolt, red hub cap.
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Front: Original version shock absorber complete with bump stops and hub cover
Rear: Black painted shock absorber, complete with lower support, upper support, and fixing bolt
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Front: Original version shock absorber complete with bump stops and hub cover
Rear: Phosphated shock absorber, complete with lower support, upper support, and fixing bolt
Three-hole puller for disassembling the conical gear of the primary transmission for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Provided are no. 3 M4 screws with recessed hexagon and one central hex head screw no. 13
Required wrench: 19
Magnet flywheel fan 12 blades CNC/RACING VMC in gold anodized aluminum
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 50 PK S/XL, Vespa 125 Primavera VMA1T>2T, Vespa 125 Primavera ET3 VMB1T, Vespa 125 PK S/XL
Complete Evok "Soft Iron Clutch" for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS-Ape 50
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
EVOK "Soft Iron Clutch" Clutch Kit for Vespa Smallframe (Up to 18 HP)
Are you looking for the perfect combination of lever smoothness and impeccable grip? The EVOK Soft Iron Clutch Kit is specifically designed for all Vespa Smallframe with power up to 18 HP.
Resulting from the continuous research and development of the Italian brand, this kit represents the perfect bridge between the original spare part and high performance: it guarantees significantly higher stress resistance without sacrificing everyday modulatability.
🌟 WHY CHOOSE THE EVOK SOFT IRON CLUTCH?
CNC Engineering from Solid: The clutch body is made of CNC aluminum with hard anodizing treatment in the iconic EVOK orange color, while the inner basket is made from solid hardened steel for maximum longevity.
Kevlar Ferodo Racing Discs: Includes Kevlar-lined discs developed in collaboration with Ferodo Racing, designed to withstand high temperatures and eliminate slipping issues.
All models
Practical packaging with reduced dimensions, essential for on-the-road repairs.
The kit contains:
1 Long nose pliers
1 Wire cutter
1 Flathead screwdriver
1 Phillips screwdriver
1 Bit holder
10 Bits
1 Extension
7 Sockets (11/10/9/8/7/6/5 mm)
5 Wrenches (6/5/4/3/2 mm)
Pair of black grips with Malossi MHR BLACK logo for Vespa 50/90/125 Primavera ET3/GTR/Sprint V/TS/Rally/PX
Vespa 50/90/125/150/200
The new Malossi MHR grips aim for a trio of elements: design-Safety-comfort.
Every detail has been designed and defined based on these three elements, essential for an aggressive design, secure grip, and comfort while riding.
In particular, the design favors vibration absorption, the dimensions make the grip secure and manageable, and the ergonomic structure allows the palm to rest without inflaming the forearm.
The Malossi MHR BLACK grips are made with a thermoplastic rubber with high mechanical characteristics and excellent heat resistance, the result of extensive research aimed at selecting special polymers with high elasticity and soft touch. This material ensures the MHR BLACK grips' resistance in all usage conditions and, consequently, great durability. Finally, the soft touch conveys a sensation of pleasure and comfort to the user.
Piston for Pinasco thermal group (80 cc) in cast iron for Vespa 50 N-L-R-Special-PK-XL-N-HP-FL-Ape 50
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 50 PK, Ape 50
Stroke: 43
Displacement: 80 cc
Rollbar tube reinforcement 360 Project Garage 2.1 for Vespa 50 V5A1T L/R-Special V5A2>3T/V5B1>4T-90 V9A1T/125 Primavera ET3- 50/125 PK-S-XL-N-HP-FL-80/125/150/160/180/200 PX-PE-Sprint-TS-GL-Rally-VNB-VBB
Vespa 50 V5A1T L/R-Special V5A2>3T/V5B1>4T-90 V9A1T/125 Primavera ET3 Vespa 50/125 PK-S-XL-N-HP-FL
Vespa 80/125/150/160/180/200 PX-PE-Sprint-TS-GL-Rally-VNB-VBB
Reinforcement bar for Vespa Smallframe Frame 2.1 360 PG CNC
Specific reinforcement bar for the Vespa Smallframe frame, designed to improve structural rigidity while maintaining the correct elasticity of the frame.
The 360 PG CNC bar allows for adjusting the tension or compression of the frame cradle, enabling you to adapt the reinforcement to your needs without compromising the structure's flexibility.
Installation is done via front fastening in the holes intended for the spare wheel support and rear fastening at the height of the bag hook.
Finish and materials: Polished steel and CNC machined aluminum
WARNING: For the rear fastening, 2 holes must be made on the frame.
Full CNC gear selector CRIMAZ for Vespa 50 N/L/R-Special-90 V9A1T-125 Primavera ET3
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 Primavera VMA1T>2T
full CNC gear selector kit, with solid stem.
CRIMAZ CNC mesh
cemented and drilled CNC pads to promote lubrication
coupling with M6 nut cam
Complete shock absorber -P&A- for Vespa 50/125 Special-PK-Primavera
Vespa 50 V5A1T L (adaptable / Adaptable Vespa 50 V5A1T N,R)
Vespa 50 Special V5A2T>3T
Vespa 50 Special V5B1>4T
Vespa 50 V5SS1T
Vespa 50 PK S
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 90 V9SS1T
Vespa 125 Primavera VMA1T>2T
Gray plastic sheath
Floating pin clip of Garden MA/UA/UB23S3 for Vespa 125 VNA/150 VB/VL/GS
Vespa 125 VN2/VB/VL/VNA/150 VB/VL/GS
Complete thermal group Pinasco (80 cc) in cast iron for Vespa 50 N-L-R-Special-PK-XL-N-HP-FL-Ape 50
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 50 PK, Ape 50
Stroke: 43
Displacement: 80 cc
All models / Tutti i modelli
Barrel: 8x8 mm
Length: 2200 mm
Diameter: 1.86 mm
All Models
Diameter: 1.2 mm
Length: 2000 mm
Barrel: 2.8x3 mm