Ø 115 mm
with discs
28 spring(s)
2 washers
thickness 1.15mm

Recommended for racing use
- 4 discs
- 8 springs

Kit composed of--> 3 cork discs, 2 metal discs, locking ring
Attention--> Kit compatible with clutch 07-BO-046-DT

Reinforced basket, 12 springs (with different hardnesses to configure the product according to one's needs), 4 cork discs, 4 metal discs, fully machined dovetail engagement system. Tested on engines up to 38 HP.
Attention: for mounting on 125/150 engines, some casting "ribs" on the cover and crankcase must be shaved.

The CMX is defined as a turned clutch because the basket is integral with the gear (pinion). This technical choice allows the basket (commonly known as the
bell) to remain stationary when the clutch is pulled (clutch disengagement).
Thanks to this reversal of moving parts, the clutch
becomes much more progressive in the initial thrust phase of the Vespa
minimizing any annoying jerks at start-up
(a problem known to old-design clutches). This precaution,
together with the significant contact points of the lined discs and conducting discs,
makes the CMX an ideal clutch for engines with power
greater than 15 hp, avoiding premature wear caused by the
hammering of the contact parts.

BGM PRO Super Strong clutch What is a plug and play solution - Made
in Germany. You get a ready-to-install clutch product with reinforced
clutch springs that works well in a power range up to 20hp / 22Nm. With
stiff springs available separately, the clutch does not disappoint, even with configurations of more than 40 hp.

BGM PRO Super Strong clutch is a plug and play solution - Made
in Germany. You get a ready-to-install clutch product with reinforced
clutch springs that works well in a power range up to 20hp / 22Nm. With separately available stiff springs, the clutch does not disappoint, even with configurations of more than 40 hp.

Sviluppati per le prestazioni e le coppie decisamente elevate dei
motori odierni, sono realizzati in acciaio altamente legato (SCM415/15
CrMo 5), nel rispetto dei massimi standard produttivi. L’enorme
resistenza del materiale di base (fino a 1100N/mm2, HRC 58-62) è un
fondamento sicuro per la produzione dei pignoni BGM.

La
produzione soddisfa gli alti standard vigenti per la produzione di
ingranaggi di Honda. Ogni singolo pezzo è accompagnato da un verbale di
collaudo, consentendo così a BGM di disporre di un’assicurazione della
qualità continua e duratura.

Materiale di alta qualità 15 CrMo 5
Produzione precisa secondo gli standard Honda
Controlli qualità continui
Compatibile con frizioni per COSA2
Disponibile con 22, 23 e 24 denti
Compatibile con le primarie originali di tutti i motori 200 c.c.
Compatibile con motori con primaria originale riequipaggiata con 65 denti o con primaria BGM con 64/65 denti

Nuova soluzione ad 8 molle per vespa Wideframe e Largeframe.
La frizione è stata pensata e studiata per quegli usi estremi dove il calore e la scarsa lubrificazione la fanno da padrone. Grazie all’utilizzo di dischi con particolari caratteristiche ed impiegati su Vespa Smallframe, la frizione ha una
geometria nuova. Infatti sia il cestello che i disco di traino sono
stati realizzati per potersi assemblare con dischi da Smallframe. Anche
il rasamento e la bronzina dove scorre il pignone della primaria sono
stati curati nelle tolleranze di accoppiamento e nella qualità del
materiale. Una particolare geometria del cestello e dell’anello di
chiusura la rendono affidabile nel suo funzionamento estremo.
La frizione è ricavata dal pieno con lavorazione al CNC, di materiale performante che subisce un trattamento di brunitura a fine lavorazione.
Viene fornita con 8 molle, 8 bicchierini, 4 dischi e 3 infradischi. Il
fatto di avere 8 molle permette di poter utilizzare diverse tipologie di
molle (durezze diverse in funzione delle potenze del motore) ed avere
sempre un carico distribuito omogeneo. Lavorando su di un diametro molto
grande permette la trasmissione di carichi importanti.
Diametro 107 mm, monta pignoni PX

Nuova soluzione ad 8 molle per vespa Wideframe e Largeframe.
La frizione è stata pensata e studiata per quegli usi estremi dove il calore e la scarsa lubrificazione la fanno da padrone. Grazie all’utilizzo di dischi con particolari caratteristiche ed impiegati su Vespa Smallframe, la frizione ha una
geometria nuova. Infatti sia il cestello che i disco di traino sono
stati realizzati per potersi assemblare con dischi da Smallframe. Anche
il rasamento e la bronzina dove scorre il pignone della primaria sono
stati curati nelle tolleranze di accoppiamento e nella qualità del
materiale. Una particolare geometria del cestello e dell’anello di
chiusura la rendono affidabile nel suo funzionamento estremo.
La frizione è ricavata dal pieno con lavorazione al CNC, di materiale performante che subisce un trattamento di brunitura a fine lavorazione.
Viene fornita con 8 molle, 8 bicchierini, 4 dischi e 3 infradischi. Il
fatto di avere 8 molle permette di poter utilizzare diverse tipologie di
molle (durezze diverse in funzione delle potenze del motore) ed avere
sempre un carico distribuito omogeneo. Lavorando su di un diametro molto
grande permette la trasmissione di carichi importanti.
Diametro 107 mm, monta pignoni PX

BGM PRO Super Strong clutch What is a plug and play solution - Made
in Germany. You get a ready-to-install clutch product with reinforced
clutch springs that works well in a power range up to 20hp / 22Nm. With
stiff springs available separately, the clutch does not disappoint, even
with configurations of more than 40 hp.

The Superstrong 2.0 CR joint combines extreme durability, absolute reliability, and ease of use. It is the foundation of every solid engine tuning.
The solid CNC-machined clutch basket has excellent
concentricity and enormous torsional rigidity. It therefore offers a perfect
clutch engagement with a well-defined bite point and a clean cut. It is suitable for both the touring rider who appreciates high quality,
and the ambitious racer looking for an extremely robust and
stable clutch. ULTRALUBE The latest generation Superstrong 2.0 CR clutches are now equipped with a new innovative technology: Ultralube. Ultralube
delivers (through precisely defined holes and centrifugal force)
gear oil both in the high-load hub profile (between the
clutch basket and the clutch hub) and in the clutch linings themselves. This technology, unique in the Vespa sector,
makes the legendary Superstrong 2.0 CR clutch even more stable than
it already is. A clutch designed for eternity. PERFORMANCE
The clutch provided ready for installation is adjusted for a
power range up to approx. 20PS /

- Complete clutch with basket and shock absorbers
- 4 discs
- 8 springs

- Complete clutch with basket and damper
- 4 discs
- 8 springs

The Superstrong 2.0 CR clutch combines extreme durability, absolute reliability, and ease of use. It is the foundation of every solid engine tuning. The solid CNC-machined clutch basket has excellent concentricity and enormous torsional rigidity. Thus, it offers perfect clutch engagement with a well-defined biting point and a clean cut. It is suitable for both the touring rider who appreciates high quality and the ambitious racer seeking an extremely robust and stable clutch.

The bgm PRO clutch springs are produced in Germany and are subject to continuous quality control. The material used, Oteva70®, makes the spring block stable and true to size. The spring does not deviate laterally until it is blocked, and once unloaded, it returns to its original length. The clutch spring retains all its elastic strength. The spring rate is significantly tighter than that of an original spring. Ideal for high-performance engines.

Smart MRP solution to continue drawing cold air from the frame when using larger carburetors.

The opening in the frame measures approximately 60x44mm. The area is therefore equivalent to a carburetor with a cross-section greater than Ø50mm. Thus, the intake pipe solution offers no performance loss even on very powerful engines. Thanks to the cooler intake air, better results can be expected under heavy load, which otherwise strongly heats the intake air under the side cover.

Another great advantage is that the frame can also be used as sound insulation. Engines that have been converted to diaphragm-controlled intake can thus drastically reduce the noise level of the intake air. For this purpose, the frame can be further lined from the inside with sound-absorbing material.

The advantages are a lighter clutch that separates more quickly and is extremely durable.
Despite the seemingly smaller pad surface, the clutch with the CR pad type can transmit more torque with the same elastic force. For this, only the effective radius is decisive, not the size of the friction surface as such (this is only relevant for wear).

Thanks to the extremely durable pad material, CR pads can also be used in very powerful engines in everyday use. A major advantage is the taller clutch discs compared to the
original discs.


RECOMMENDATION We also recommend a low-alloy gear oil of API GL3/GL4 classes for high-performance engines to prevent clutch slippage even under extreme loads.

Note: The entire lining package is approximately 1 mm lower with these linings

After installing the clutch, check if the clutch touches the clutch cover. If necessary, rework the whole thing or use an outward-facing cover. Alternatively, you can use the spacer ring we offer separately

The Malossi range for the Vespa offers products with extremely high technology capable of developing performance increases
so exceptional compared to the standard, that it requires the adaptation of other fundamental components
of the vehicle.

Just compare a Vespa PX 200 E produced in 1978, which originally develops a power of 12.35 HP at 5700 RPM, with a Vespa "tuned" with Malossi Kits, which can develop 27.5 HP at 8000 RPM, or more than double
HP at an extremely higher rotation speed, to understand that it was absolutely essential to design a clutch unit capable of withstanding the stresses due to a performance increase of such proportions!



The POWER UP CLUTCH SYSTEM Malossi clutch units are designed to provide a response and overcome all the problems that inevitably arise when the clutch unit technology is not adequate to the other engine components. A traditional clutch, having to transmit more than double the power to the gears, while simultaneously rotating much faster, can lead to bell failures under the effect of
centrifugal force, slipping and deformations that translate into annoying and unsettling metallic noises, up to the classic clutch slipping caused by

Compatible with our item: 07-BO-046-DT

The Superstrong 2.0 CR joint combines extreme durability, absolute reliability, and ease of use. It is the foundation of every solid engine tuning.
The solid CNC-machined clutch basket has excellent
concentricity and enormous torsional rigidity. It therefore offers perfect
clutch engagement with a well-defined slip point and a clean cut. It is suitable for both the touring rider who appreciates high quality,
and the ambitious racer who seeks an extremely robust and
stable clutch. ULTRALUBE The latest generation Superstrong 2.0 CR clutches are now equipped with a new innovative technology: Ultralube. Ultralube
delivers (through precisely defined holes and centrifugal force)
gear oil both in the high-load hub profile (between the
clutch basket and clutch hub) and in the clutch linings themselves. This technology, unique in the Vespa sector,
makes the legendary Superstrong 2.0 CR clutch even more stable than
it already is. A clutch designed for eternity. PERFORMANCE
The clutch supplied ready for installation is adjusted for a
power range up to approx. 20PS / 22Nm through

Diameter of the disc: 107mm (7-spring clutch)

for our article: 07-BO-046-DT

BGM PRO Super Strong clutch What is a plug and play solution - Made
in Germany. You get a ready-to-install clutch product with reinforced
clutch springs that works well in a power range up to 20hp / 22Nm. With separately available stiff springs, the clutch does not disappoint, even with configurations of more than 40 hp.

VMC "10 springs ERGAL" clutch for Vespa Large Frame for Piaggio Vespa "COSA" pinions

Basket in "Ergal" with hard anodization specific for VMC clutch plates or "CR80" model plates

Internal steel spider with hardening treatment complete with bushing and shim.

- 4 aluminum conductors with custom-made carbon/kevlar friction material and "CR80" type teeth.

- 4 laser-cut steel driven plates for the most precise pinion/plate coupling possible.

Clutch pack closing ring in laser-cut harmonic steel with holes for circlip pliers. 

- with the set of 10 soft springs the clutch withstands power of about 20hp
- with the set of 10 hard springs the clutch withstands power of about 35hp
- with the set of 10 Extra hard springs the clutch withstands power of about 45hp

Note: the clutch only fits with Piaggio 8 springs type "Cosa" pinions and clutch plates 

THE PINION IS NOT INCLUDED IN THE KIT

The Superstrong 2.0 CR joint combines extreme durability, absolute reliability, and ease of use. It is the foundation of every solid engine tuning.
The solid CNC-machined clutch basket has excellent
concentricity and enormous torsional rigidity. It therefore offers a perfect
clutch engagement with a well-defined bite point and a clean cut. It is suitable both for the touring rider who appreciates high quality,
and for the ambitious racer looking for an extremely robust and
stable clutch. ULTRALUBE The latest generation Superstrong 2.0 CR clutches are now equipped with a new innovative technology: Ultralube. Ultralube
delivers (through precisely defined holes and centrifugal force)
gear oil both into the high-load hub profile (between the
clutch basket and the clutch hub) and into the clutch linings
themselves. This technology, unique in the Vespa sector,
makes the legendary Superstrong 2.0 CR clutch even more stable than
it already is. A clutch designed for eternity. PERFORMANCE
The clutch supplied ready for installation is adjusted for a
power range of up to approx

Straight-tooth gear & bull clutch Pinasco

The bgm PRO clutch springs are produced in Germany and are subject to continuous quality control. The material used, Oteva70®, makes the spring block stable and true to size. The spring does not deviate laterally until it is blocked, and once unloaded, it returns to its original length. The clutch spring retains all its elastic force. The spring rate is significantly narrower than that of an original spring. Ideal for high-performance engines.

The Polini "HT Clutch for Race" is an innovative racing clutch designed for the most demanding riders. Designed for Vespa Largeframe, it offers exceptional performance thanks to advanced technologies.

Main features:

-Reduced mass on the crankshaft and numerous adjustment options.
-Suitable for high torque.
-Lightweight aluminum construction to improve performance.
-Needle bearing to reduce friction and improve shifting.
-Aluminum friction discs to optimize grip and power transmission.