RDV Scootershop
RDV > Spare Parts and Accessories > Shield > Shield edges > White shield protection gasket for Vespa 50-125/PV/ET3/125 VNA-TS/150 VBA-Super/160 GS/180 SS/Rally/PX80-200/PE/Lusso/T5
White shield protection gasket for Vespa 50-125/PV/ET3/125 VNA-TS/150 VBA-Super/160 GS/180 SS/Rally/PX80-200/PE/Lusso/T5
Available
10-BV-238-IR

White shield protection gasket for Vespa 50-125/PV/ET3/125 VNA-TS/150 VBA-Super/160 GS/180 SS/Rally/PX80-200/PE/Lusso/T5

Original reference: 86064000

Shipping time:

24/48 hours

1 point RDV = 2 cents 9 points RDV = 0,18 € cashback
9,90 €
8,11 € VAT excluded

Related articles

-5% Continental conti-twist tire 3.00/10 M/C
Available
Available
01-FA-032-RM
01-FA-032-RM

Continental conti-twist tire 3.00/10 M/C

Compatibility

Vespa 50 V5B1>4T
Vespa 50 V5SA1T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa PK
Vespa 125 Primavera ET3 VMB1T

technical specifications

Load Index: 50M

Notes: Tubeless

Approfondisci
Shipping time
24/48 hours
47,97 € 50,49 €
39,32 € VAT excluded
1 point RDV = 2 cents 47 points RDV = 0,94 € cashback
BGM Pro Clutch Gear - Pro Superstrong Z 23 for 64/65 Tooth Elastic Gear Vespa 200-PX-PE-Rally
low availability
Compatibility

Vespa 200 PE
Vespa 200 Rally

technical specifications

Developed for the high performance and torque of today's engines, they are made of high-alloy steel (SCM415/15 CrMo 5), in compliance with the highest production standards. The enormous strength of the base material (up to 1100N/mm2, HRC 58-62) is a secure foundation for the production of BGM sprockets.

The production meets the high standards in force for Honda gear production. Each individual piece is accompanied by a test report, thus allowing BGM to have continuous and lasting quality assurance.

High quality material 15 CrMo 5
Precise production according to Honda standards
Continuous quality checks
Compatible with COSA2 clutches
Available with 22, 23, and 24 teeth
Compatible with the original primaries of all 200 c.c. engines
Compatible with engines with original primary retrofitted with 65 teeth or with BGM primary with 64/65 teeth

Approfondisci
69,00 €
56,56 € VAT excluded
1 point RDV = 2 cents 69 points RDV = 1,38 € cashback
Roller bearing differential box (25x33x16) for Ape 50 TM/P50/FL/FL2FL3 Europa/Mix/RST Mix
Available
Compatibility

Ape 50 TM/P50/FL/FL2FL3 Europe/Mix/RST Mix

Approfondisci
Shipping time
24/48 hours
8,00 €
6,56 € VAT excluded
1 point RDV = 2 cents 8 points RDV = 0,16 € cashback
Gearbox shaft with 2 holes for cruciform alignment for Vespa 50-90-125 Primavera/ET3/PK
low availability
Compatibility

Vespa 50 V5A1T N/L/R 92877>

Vespa 50 S V5SA1T 111891>

Vespa 50 Special V5A2T>3T

Vespa 50 Special V5B1>4T

Vespa 90 V9A1T 25001>

Vespa 125 Primavera VMA1T>VMA2T

Vespa 125 Primavera ET3 144679>

Vespa 50/125 PK S/XL/N/HP

technical specifications

The new reinforced axle for Vespa smallframe engines is
made of high-strength steel with a related vacuum carburizing treatment.

The material used and the new sizing make the axle
particularly suitable for tuned engines or with displacements higher
than normal (even up to 250 ccm)

Today, thanks to recent investments by some manufacturers, it is
possible to find a wide range of very powerful thermal units on the market
that even exceed 40 horsepower.

I remind you that the Vespa smallframe engine was designed to last over
time and its power hardly exceeded 10 horsepower.

With these power increases, it is essential to adapt all the mechanisms to avoid breakages and premature wear.

Example of the new sizing. The threading has also been increased to M16x1.25

Approfondisci
195,00 €
159,84 € VAT excluded
1 point RDV = 2 cents 195 points RDV = 3,90 € cashback