Extractors and related
Flywheel puller tool M28x1 for Vespa 50-125/PV/ET3/PK50-125/S/XL/XL2/125 GT-TS/150 GL-Super/200 Rally/PX80-200/PE/Lusso/'98/MY/'11/T5/Cosa
Vespa 50
Vespa 50 PK
Vespa 125 PK/S/XL/
Vespa 125 ET3
Vespa 125 GT/TS
Vespa 150 GL/Super
Vespa 180/200 Rally
Vespa PX/PE/T5/Cosa
Size: 28x1
All models
The ignition timing is important for the thermal health of the
engine and for delivering full power. If you rebuild the
engine, you should not rely on existing marks for
ignition adjustment, but measure it personally. This is
easily possible with this electronic timing gun for
gasoline engines with contact or transistor ignition system
(CDI ignition as in series with ET3, PK, PX, PX, Cosa, T5 etc.) 6 and 12-volt ignitions can be adjusted at both 6 and 12 volts. Note:
It doesn't matter if the ignition is 6V or 12V, an external 12-volt power source (e.g. a car battery) is always needed if the
vehicle doesn't already have one.
A super bright xenon tube and a special converging lens ensure optimal visibility of the fixed markers even at speeds over 8000 rpm in the near field.
The gun is connected to a 12-volt battery via the crocodile clips and the inductive clip on the spark plug cable (without direct contact
with the wire)
Crankshaft disassembly tool clutch side Vespa 50 N/L/R- Special-125/PV/ET3/PK50-125/S/SS/XL/XL2
Vespa 50 N/L/R- Special-125/PV/ET3/PK50-125/S/SS/XL/XL2
All models
The ignition timing is important for the thermal health of the
engine and for delivering full power. If you rebuild the
engine, you should not rely on existing marks for ignition
adjustment, but measure it personally. This is
easily possible with this electronic timing gun for
gasoline engines with contact or transistor ignition system
(CDI ignition as in series with ET3, PK, PX, PX, Cosa, T5, etc.) The 6 and 12 volt ignitions can be adjusted at both 6 and 12 volts. Note:
It doesn't matter if the ignition is 6V or 12V, an external 12 Volt power source is always required (e.g. a car battery) if the
vehicle doesn't already have one.
A super bright xenon tube and a special converging lens ensure optimal visibility of the fixed markers even at speeds above 8000 rpm in the near field.
The gun is connected to a 12-volt battery via the crocodile clips and the inductive clip on the spark plug wire (without direct contact with the wire)
Piaggio YES-HELLO-Bravo-Cricket
M17 x 1mm
Medium strength threadlocker "LOCTITE 243" locks nuts, screws, bolts, studs (10ml)
All models
SIP Extractor Tool for flywheel side gearbox shaft bearing for Vespa 50/90/125/Primavera//ET3/PK50-125/S/XL/XL2
Vespa 50 V5A1T N,L,R
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa PK
Except Vespa 50 N 1963/64 (small door)
Vespa 160 GS VSB1T
Vespa 180 SS VSC1T
Hub nut removal tool for 125 VNA/VNB/GT/GTR-150 VBA/VBB/GL/Sprint/S.Veloce/Rally
Vespa 125 Super VNC1T
Vespa 125 VNA1>2T
Vespa 125 VNB1>6T
Vespa 125 GT VNL2T> 76107
Vespa 125 GTR VNL2T> 118278
Vespa 150 Super VBC1T
Vespa 150 VBA1T
Vespa 150 VBB1>2T
Vespa 150 GL VLA1T
Vespa 150 Sprint VLB1T >1151814
Vespa 150 Sprint V. VLB1T> 0165002
Vespa 180 Rally VSD1T
High-quality tool, redesigned by our staff to make it more resistant, the teeth of each individual piece have been hardened and subsequently burnished.
Replacement weights for extractor 07-FQ-055-IR flywheel side bearing 20x47x14 mm for Vespa 50 2°/N/L/R/S 2°/Special/SR/SS/PK50/S/SS/XL/XL2/Ape 50
Vespa 50 2°/N/L/R/S 2°/Special/SR/SS/PK50/S/SS/XL/XL2/Ape 50
For bearing dimensions: 20x47x14 mm
Gear shaft disassembly tool for Vespa 50-125/PV/ET3/PK50-125/S/XL/XL2
Vespa 50-125/PV/ET3/PK50-125/S/XL/XL2
Engine stud removal tool set for Vespa 90/125/150/180/200 all models
All models
Measurements in the kit:
M6x1.0 mm/M7x1.0 mm/M8x1.25 mm
Piaggio Vespa
Bottle 300 ml
Clutch ring disassembly tool for Vespa 125 V1-TS/150 VL-Super/160 GS/180 SS/Rally/PX80-200/PE/Lusso -> 1994/Cosa 1/T5
vespa 125
vespa 150
Vespa 160
Vespa 180
Vespa 200
All except 125 primavera -ET3
Telescopic tool -CHILITEC- Magnetic tool, total length 16-61cm, pulling force approximately 2kg
All models
Disassembly/Reassembly Tool for Gear Shaft Ring for Vespa VM/VN-150 GS/VL1
Vespa 125 VM1T>VM2T
Vespa 125 VN1T>VN2T
Vespa 150 GS VS1T>VS5T
Vespa 150 VL1T>VL3T
Vespa 150 VB1T
Vespa 150 GL VGL1T
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 125 Primavera VMA1T>2T, Vespa 125 Primavera ET3 VMB1T
Clutch pack stop tool (to facilitate disassembly) Vespa 125 VNA–TS/150 VBA -T4/160 GS/180 SS/Rally/PX80 -200/PE/Lusso/´98/MY/´11/T5 /Cosa
Vespa 125/150/160/180/200
Vespa 125/150/160/180/200
Vespa 125/150/160/180/200
Piaggio Ciao,Yes,Bravo,Boxer,Cricket
Vespa 125 PX VNX1>2T
Vespa 125 PX ZAPM 74100
Vespa 125 TS VNL3T 18139>
Vespa 125 GTR VNL2T 145901>
Vespa 125 Cosa VNR1T
Vespa 150 Cosa VLR1T
Vespa 150 Sprint Veloce VLB1T 294260>
Vespa 150 Super VBC1T 412374>
Vespa 150 PX 2011 ZAPM 74200
Vespa 125/150/200 Cosa
Vespa 150 GS VS1>5T
Vespa 160 GS VSB1T
Vespa 180 SS VSC1T
Dimensions: mm 23x1.5
Rear pulley locking tool for Vespa 125/150/250/300 ET4/LX/LXV/S /Primavera/Sprint/GTS/GTS Super/GTV/GT 60/GT/GT L 125
Vespa ET4/LX/LXV/S/Primavera/Sprint/GTS/GTSSuper/GTV/GT 60/GT/GT L
Crankshaft assembly tool flywheel side (large cone M12 mm) Vespa 50 N/L/R- Special-125/PV/ET3/PK50-125/S/SS/XL/XL2
Vespa 50 N/L/R- Special-125/PV/ET3/PK50-125/S/SS/XL/XL2
Flywheel puller 27x1 mm Vespatronik Quattrini for Vespa 50/90/125 Primavera ET3/PK
Vespa 50 V5A1T N,L,R, Vespa 50 Special V5A2>3T, Vespa 50 Special V5B1>4T, Vespa 50 PK S/XL, Vespa 125 Primavera VMA1T>2T, Vespa 125 Primavera ET3 VMB1T, Vespa 125 PK S/XL
Calibrated punch roller bearing assembly gearbox shaft for Vespa 125 GT 2°/GTR/Super 2°/TS/150 GL 2°/Sprint 2°/V/Super 2°/Rally/PX80-200/PE/Lusso/T5/Cosa
Vespa 125 Super VNC1T 024900>
Vespa 125 GT VNL1T 60900>
Vespa 125 GTR VNL2T
Vespa 125 TS VNL3T
Vespa 125 PX VNX1>2T
Vespa 125 PX T5
Vespa 150 Super VBC1T 70200>
Vespa 150 Sprint VLB1T 73900>
Vespa 150 Sprint Veloce VLB1T
Vespa 150 PX VLX1T
Vespa 180 Rally VSD1T
Vespa 200 Rally VSE1T
Vespa 200 PE VSX1T
For bearings sizes:
28x35x13 mm
28x38x15
Calibrated punch for mounting bearing 25x62x12 and oil seals 20x62x6.5/ 31x62.1x5.8/4.3
for Vespa 125 V30-TS/150 VL-Super/160 GS/180 SS/Rally/PX80-200/PE/Lusso/T5/Cosa
clutch side oil seal fitting for Vespa 125 VNA2
2°/VNB/GT/GTR/Super/TS/150 VBA
2°/VBB/VGLA/B/GL/Sprint/V/Super/Rally/PX80-200/PE/Lusso/T5/Cosa
Ø19.5/62 mm
Fabbri Racing Clutch Group Extractor Tool for Vespa 50-125/PV/ET3/PK50-125/S/XL/XL2
Vespa 50 V5A1T N,L,R
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa PK
VESPA clutch extractor Allows you to replace worn clutch discs without having to remove the hub from the engine. To also disassemble the internal hub, by removing the external core supplied with the extractor, it is possible to proceed with disassembly like a normal vespa extractor.
All models