Front left indicator for Vespa GTS/GTS Super/GTV/GT 60/GT/GT L 125-300ccm
Original reference: PI5849710
Bulb included (W2.1x9.5d)
Vespa 125 GT L ( Euro 3 ) ZAPM31100 4T LC
Vespa 125 GT L ZAPM31101 4T LC
Vespa 125 GT ZAPM31100 4T LC
Vespa 125 GTS Super i.e.ZAPM45300 / ZAPM45301 4T LC
Vespa 125 GTS Super Sport ZAPM45300 4T LC
Vespa 125 GTS ZAPM31300 4T LC
Vespa 125 GTV ZAPM31301 4T LC
Vespa 200 GT 60° i.e. ZAPM45102 4T LC
Vespa 200 GT L ZAPM31200 4T LC
Vespa 200 GT ZAPM31200 4T LC
Vespa 250 GTS i.e. ABS ZAPM45101 4T LC
Vespa 250 GTS i.e. ZAPM45100 4T LC
Vespa 250 GTV i.e.
Related articles
Vespa 50 V5A1T N/L/R
Vespa 50 Special
Vespa 50 PK
Primary transmission pair TOP Crimaz z26 on bell 69 with reinforced clutch basket and shock absorber for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module gear shaper tool
1.5 with relative corrections for the sprockets added to the original
pair.
The tooth width has been widened (1 mm towards the inside) to
achieve greater resistance without compromising smoothness.
The spring seats have been revised to use springs with square wire. The greater travel of the damper preserves the gearbox and cruise.
In the center, there is a roller bearing on the most
stressed part and a guide bushing on the shaft. This solution
allows the bell to be compatible with the original starting
gears.
Vespa 98
- Vespa 125 from '48 to '65
- Vespa 150 from '54 to '66
90-degree valve
3.50/8,4.00/8
Silent-block traversa motore MD Racing neri (soft) Alluminio/poliuretano per carter motore originali Piaggio Vespa V50, V90, SS50, SS90, PV125, ET3, PK S, PK XL
Vespa 50 V5A1T 92877>
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1T>3T
Vespa 50 PK
Vespa 90 V9A1T 25001>
Vespa 90 SS V9SS2T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Speciale Kit silent block ANTERIORE per vespa small (vespa 50 ,special , ET3,PK, HP) realizzato interamente in ERGAL ricavato dal pieno e poliuretano di altissima qualità, con densità calcolata per il massimo confort.
La specifica filettatura al centro dei perni con invito facilitato, risolve il problema di montaggio.
E’ sufficiente una volta inseriti i perni destro e sinistro, avvitare le due estremità mediante due chiavi a brugola da 10mm inserendole nell’apposita cava in testa al perno e serrare fino a battuta.
In questo modo si è sicuri che la lunghezza perno sia corretta e soprattutto definita.
Vengono fornite assieme al kit 02 rasamenti da 1mm per creare la battuta interna ai gommini.