CCcorsa gasket kit for Cylinder group and reed valve block for Vespa 125 VM1>2T/VN1>2T
Vespa 125 VM1>2T
Vespa 125 VN1>2T
Vespa 150 VL1>3T
Vespa 150 VB1T
Related articles
CRANKSHAFT SEAL 20X40X7 Corteco (MODIFICATION FOR EXTERNAL SEALS) FOR VESPA 125 VM/VN-150 VL/VB1T/VNA1T
Vespa 125 VM1T > VM2T
Vespa 125 VN1T > VN2T
Vespa 125 VNA1T
Vespa 150 VL1>3T
Vespa 150 VB1T
Note--> Lower the thickness to 6 mm.
Crankshaft oil seal 20X40X7 in Viton double lip (modification of external oil seals) for Vespa 125 VM/VN-150 VL/VB1T/VNA1T
Vespa 125 VM1>2T
Vespa 125 VN1>2T
Vespa 125 VNA1T
Vespa 150 VL1>3T
Vespa 150 VB1T
Note--> Reduce the thickness to 6 mm.
Complete 4-speed Pinasco gearbox for Vespa 125 VM1>2T-VN1>2T-VL1>3T-VB1T
Vespa 125 VM1T (Adaptable-adaptable)
Vespa 125 VM2T (Adaptable-adaptable)
Vespa 125 VN1T
Vespa 125 VN2T
Vespa 150 VL1T
Vespa 150 VL2T
Vespa 150 VL3T
Vespa 150 VB1T
Complete with multiple shaft, WITHOUT selector
For VM1>2T versions support and starting gear with bushing.
Gear teeth: 57-52-47-43
Multiple teeth: 13-18-23-27
Multiple bearing: 12x37x12
WURTH sealant based on silicone Super RTV with high torque capacity - 200ml
Content: 200 ml
Chemical base: Neutral curing silicones, oxime base
Odor/fragrance: Characteristic
Skinning time min: 5 min
Conditions for skinning time: compliant with ASTM D-4678
Full cure rate: 2 mm/g
Conditions for full cure: 23°C and 50% relative humidity
Shore A hardness: 40
Tensile strength min.: 2.2 N/mm²
Conditions for tensile strength: compliant with ASTM D-412
Conditions for maximum elongation at break: 300% / compliant with ASTM D-412
Thermal conductivity λ: 0.2 J/(m*s*K)
Conditions for thermal conductivity λ: in compliance with ASTM D-2214/70
Coefficient of thermal expansion: 0.0002 1/K
Conditions for coefficient of thermal expansion: compliant with ASTM EB-31
Dielectric strength: 16 kV/mm
Conditions for dielectric strength: compliant with ASTM D-149
Dielectric constant: 2.8
Conditions for dielectric constant: 1 MHz, ASTM D-150
Dissipation factor
BGM PRO crankshaft bearing and oil seal kit FKM/Viton® (E10/ethanol resistant) for Vespa 125/150 VM/VN/VL/VB1T/VNA/GS
Vespa 125/150 VM/VN/VL/VB1T/VNA/GS
WIDE FRAME ENGINE ISSUE: The BGM Pro and Corteco oil seals, of much higher quality, are available (for safety reasons) only with a 0.8 mm sheet metal coating. If installed in a wide frame engine, the crankshaft bearings deform, causing damage to the bearings.
WIDE FRAME ENGINE SOLUTIONS: The circumferential bead of the oil seal is flattened, reducing the height of the oil seal plate by approximately 0.3 mm. The bearings then move freely. b) The BGM Pro bearing set with special FAG 9-ball bearings. In this case, the bearing shoulders have been precisely machined to ensure stress-free mounting of the crankshaft bearing. The set includes high-quality, durable BGM Pro FKM/Viton® oil seals.