Classic Vespa
Primary transmission pair TOP Crimaz z26 on bell 69 with reinforced clutch basket and shock absorber for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module gear shaper tool
1.5 with relative corrections for the sprockets added to the original
pair.
The tooth width has been widened (1 mm towards the inside) to
achieve greater resistance without compromising smoothness.
The spring seats have been revised to use springs with square wire. The greater travel of the damper preserves the gearbox and cruise.
In the center, there is a roller bearing on the most
stressed part and a guide bushing on the shaft. This solution
allows the bell to be compatible with the original starting
gears.
TOP Crimaz primary transmission pair z26 on bell 69 with reinforced clutch basket and shock absorber for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module gear hob
1.5 with relative corrections for the pinions added to the original
pair.
The width of the tooth has been widened (1 mm towards the inside) to
achieve greater resistance without compromising smoothness.
The spring seats have been revised to use springs with square wire. The greater travel of the shock absorber preserves the gearbox and the cruise.
In the center, there is a roller bearing on the most
stressed part and a guiding bushing on the tail. This solution
allows the bell to be compatible with the original starting gears.
Primary transmission pair TOP Crimaz z25 on 69 bell with reinforced clutch basket and shock absorbers for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module hob
1.5 with relative corrections for the pinions added to the original
pair.
The width of the tooth has been widened (1 mm towards the inside) to
have greater resistance without compromising smoothness.
The spring seats have been revised to use springs with square wire. The greater travel of the shock absorber protects the gearbox and cruise.
In the center there is a roller bearing on the most
stressed part and a guide bushing on the shaft. This solution
allows the bell to be compatible with the original starting
gears.
Primary transmission pair TOP Crimaz z25 on 72 bell with reinforced clutch basket and shock absorber for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module gear shaper
1.5 with relative corrections for the pinions added to the original
pair.
The width of the tooth has been widened (1 mm inward) to
provide greater strength without compromising smoothness.
The spring seats have been revised to use springs with square
wire. The greater travel of the shock absorber preserves the gearbox and clutch.
In the center, there is a roller bearing on the most
stressed part and a guide bushing on the shaft. This solution
allows the bell to be compatible with the original starting
gears.
Primary transmission pair TOP Crimaz z24 on 72 bell with reinforced clutch basket and shock absorber for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module 1.5 gear shaper tool with relative corrections for the pinions added to the original pair.
The width of the tooth has been widened (1 mm inward) to have greater resistance without compromising smoothness. The spring seats have been revised to use springs with square wire. The greater stroke of the shock absorber preserves the gearbox and the cruise. In the center, there is a roller bearing on the most stressed part and a guide bushing on the shaft. This solution allows the bell to be compatible with the original starting gears.
Primary transmission pair TOP Crimaz z23 on bell 72 with reinforced clutch basket and shock absorber for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module
1.5 gear shaper tool with relative corrections for the pinions added to the original pair.
The width of the tooth has been widened (1 mm towards the inside) to
provide greater resistance without compromising smoothness.
The spring seats have been revised to use springs with square wire. The greater stroke of the shock absorber preserves the gearbox and cruise.
In the center, there is a roller bearing on the most
stressed part and a guide bushing on the shaft. This solution
allows the bell to be compatible with the original starting gears.
Primary transmission gear pair TOP Crimaz z22 on 72 bell with reinforced clutch basket and shock absorbers for Vespa 50/125 Special-Primavera-ET3
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
The construction of the teeth is carried out with a module 1.5 gear cutter tool with relative corrections for the pinions added to the original pair.
The width of the tooth has been widened (1 mm towards the inside) to have greater resistance without compromising smoothness.
The spring seats have been revised to use springs with square wire. The greater stroke of the damper preserves the gearbox and the driveshaft.
In the center, there is a roller bearing on the most stressed part and a guide bushing on the shaft. This solution allows the bell to be compatible with the original starter gears.
Bevel gear primary transmission pair z25 on crown z61 DE for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged on the key
seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong type lock
on the fixing nut and to respect the tightening torque of 60-70 Nm.
For disassembly, a 3-thread puller is required, not included.
Bevel gear primary transmission pair z24 on crown z61 DE for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged on the
key seat.
The cone is compatible with the entire range of Piaggio
crankshafts and interchangeable. It is recommended to apply a strong type of locking agent on the
fixing nut and to respect the tightening torque of 60-70 Nm.
For disassembly, a 3-thread puller is required, not included.
Bevel gear primary transmission pair z23 on crown z61 DE for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and
for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong-type locking compound on
the fastening nut and to respect the tightening torque of 60-70 Nm.
A 3-thread puller, not included, is required for disassembly.
Bevel gear primary transmission pair z27 on crown z69 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong-type locking compound on
the fixing nut and to respect the tightening torque of 60-70 Nm.
For disassembly, a 3-thread extractor is necessary, not included.
Bevel gear primary transmission pair z26 on crown z69 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts and interchangeable. It is recommended to apply strong type threadlocker on the
fixing nut and to respect the tightening torque of 60-70 Nm.
For disassembly, a 3-thread puller is required, not included.
Bevel gear primary transmission pair z25 on crown z69 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for tuned engines and for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong type threadlocker on the
fixing nut and to respect the tightening torque of 60-70 Nm.
A 3-thread puller is required for disassembly, not included.
Bevel gear primary transmission pair z25 on crown z72 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged on the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong threadlocker on the
fastening nut and to respect the tightening torque of 60-70 Nm.
A three-thread puller is required for disassembly, not included.
Bevel gear primary transmission pair z24 on crown z72 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong type locking agent on the
fastening nut and to respect the tightening torque of 60-70 Nm.
For disassembly, a 3-thread puller is required, not included.
Bevel gear primary transmission pair z23 on crown z72 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and pinion.
With this system, the key does not need to be used. Ideal
for modified engines and for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply strong-type threadlocker on the
fastening nut and to respect the tightening torque of 60-70 Nm.
For disassembly, a 3-thread puller is required, not included.
Bevel gear primary drive pair z22 on crown z72 DD for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Equipped with a self-locking cone capable of stably coupling the crankshaft and the pinion.
With this system, the key does not need to be used. Ideal
for tuned engines and for crankshafts damaged at the key seat.
The cone is compatible with the entire range of Piaggio crankshafts
and interchangeable. It is recommended to apply a strong type of locking agent on the
fastening nut and to respect the tightening torque of 60-70 Nm.
A 3-thread extractor is required for disassembly, not included.
Complete clutch with 5 discs for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
The new CM5 is a top-of-the-range clutch that allows our
vespa/ape to function correctly with powers exceeding 30 hp
without needing to add spacers between the engine casing and the clutch casing.
It includes no. 5 guranite discs with the latest generation material (thickness 2.00mm) no. 4 hardened metal discs (thickness
1.20mm) no. 2 compression springs with increased load, full spider, circlip with anti-rotation notch, oil-taking pressure plate
with bearing, key + washer + high-strength nut. To reduce the considerable resistance of the springs on the clutch lever, it is
mandatory to use a clutch casing with rack and pinion reduction combined with a handlebar lever with a pivot-ball center distance
of at least 25.00mm.
Complete universal clutch with 4 discs for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Withstands 30hp
Includes no. 4 discs lined with latest generation material
(thickness 2.00mm) no. 3 hardened metal discs (thickness 1.20mm) no. 2
compression springs with increased load, full spider, circlip
with anti-rotation notch, oil-catching pressure plate with bearing,
key + washer + high-strength nut. To reduce the
considerable resistance of the springs on the clutch lever, it is mandatory
to use a clutch cover with rack and pinion reduction combined
with a handlebar lever with a minimum pivot-ball distance of 25.00mm.
Crimaz clutch bell with double spring seat for Vespa 50/90/125 Primavera ET3-PK/S/XL
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Born for drag racing, it optimizes the clutch operation both in release and grip.
The 2 support planes for the springs ensure that the clutch plates descend performing the correct movement.
Completely reinforced at critical points, it is made from solid high-strength steel. Designed for central spring clutches/double central spring.
Compatible with original clutch and extractor.
Crimaz intake closure cap on Quattrini Vespa V50/V90/SS50/SS90/125- ET3/PK S/PK XL engine casing
Vespa 50 V5A1T 92877>
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1T>3T
Vespa 50 PK
Vespa 90 V9A1T 25001>
Vespa 90 SS V9SS2T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
The suction cap is made of stainless steel with a thickness of 1mm. It is manufactured through laser cutting and subsequent laser marking. Useful for protecting the luggage compartment from dirt when not in use. Included are no. 4 white zinc plated T.B.E.I M6x6 screws with locking coating.
Extra short intake manifold for GT reed valve Quattrini or DEA Racing for Vespa 50/125 Special-N-L-R-ET3
The intake manifold, machined from solid, is provided already worked and ready to be installed. The reduced length and the particular taper of the duct improve the engine's response across the entire power range. Ideal for VHSB 34 LD carburetor or alternatively carburetors with a 44mm diameter connection. Compatible with all QUATTRINI reed valve cylinders for Vespa Smallframe.
Born for the track, it anchors to the engine casing on the engine pillar.
It comes with 2 anti-vibration mounts to be fixed on the bracket slots, and 2
raw sheet metal plates to be welded onto the exhaust in the ideal position.
Its total adjustability allows the exhaust to be positioned without tension, preventing it from breaking. Made of galvanized steel.
Rear caliper replacement Crimaz (caliper only) for Vespa 50/90/125 Primavera ET3/PK
Vespa 50/90/125 Primavera ET3
Vespa 50 PK S/XL
Rear brake disc Crimaz complete with screws (disc only) for Vespa 50/90/125 Primavera ET3/PK
Vespa 50/90/125 Primavera ET3
Vespa 50 PK S/XL
Diameter 155mm
Crimaz gold brake pads replacement for Vespa 50Special-125 GT/GTR/TS/150 Sprint/V/GL/P150S /Rally/PX80-200/PE/Lusso/´98 /MY/´11/T5
Vespa 50 Special-N-L-R
Vespa 125 ET3/GT/GTR/Super/TS/150 GL/Sprint/V/Super/P150S/Rally/PX80-200/PE/Lusso/´98/MY/´11/T5
Crimaz black brake pads replacement for Vespa 50Special-125 GT/GTR/TS/150 Sprint/V/GL/P150S /Rally/PX80-200/PE/Lusso/´98 /MY/´11/T5
Vespa 50 Special-N-L-R
Vespa 125 ET3/GT/GTR/Super/TS/150 GL/Sprint/V/Super/P150S/Rally/PX80-200/PE/Lusso/´98/MY/´11/T5
Complete clutch Cm Easy4r for Vespa 50 Special-N-L-R/90/125 Primavera ET3-PK-ETS
Vespa 50 V5A1T N,L,R
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 50 PK
Vespa 50 PK XL
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Withstands +20hp
Supplied with CRIMAZ multispring
Multi spring 8 springs Crimaz for Vespa 50/90/125 Specia-N-L-R-Primavera ET3/PK
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Compatible with original small frame clutches, CM EASY clutch, CM4, CM5
Crimaz type cross with thread for Vespa VNB - VBB - TS - GL - GT - SPRINT - SPRINT V
Vespa 125 VNB1>5T
Vespa 125 Super VNC1T
Vespa 125 GT VNL2T
Vespa 125 GT R VNL2T
Vespa 150 VL1>3T
Vespa 150 VB1T
Vespa 150 VBA1T
Vespa 150 VBB1T
Vespa 150 VBB2T
Vespa 150 GL VLA1T
Vespa 150 Super VBC1T
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa 160 GS VSB1T
Vespa 180 Rally VSD1T
Vespa 180 SS VSC1T
Crimaz clutch gear Z23/63 without plate for Malossi 63/24 ratios Vespa 200 Rally/PE
Vespa 200 Rally/PE
Reinforced Crimaz key kits for Vespa 125/150/180/200 VM/VN/VL/VB1T/VNB/VBB/GT/GL/GTR/Sprint/TS/PX/PE/Cosa/Rally
Vespa 98
Vespa 125 V1>15T
Vespa 125 V30>33T
Vespa 125 VU1T
Vespa 125 VM1>2T
Vespa 125 VN1>2T
Vespa 125 VNA1>2T
Vespa 125 VNB1>6T
Vespa 125 Super VNC1T
Vespa 125 GT VNL2T
Vespa 125 GTR VNL2T
Vespa 125 ts VNL3T
Vespa 125 PX VNX1T> 2T
Vespa 150 VL1>3T
Vespa 150 VB1T
Vespa 150 VBA1T
Vespa 150 VBB1>2T
Vespa 150 GL VLA1T
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa
Measurements: 4x15.4 mm
Crimaz reinforced square section shock absorber spring for Vespa 25 GT/GTR/Super VNC1T 11001-
Vespa 25 GT/GTR/Super VNC1T 11001->/TS/150 GL /Sprint/V/Super/160 GS/180 SS/Rally/PX80-200/PE/Lusso /Cosa/T5
dimensions--> d. 12mm x L. 32mm
Clutch disc driven Crimaz in metal for Vespa 180 Rally-200 PX/PE/Rally/Cosa
Vespa 180 Rally VSD1T
Vespa 200 Rally VSE1T
Vespa 200 PE VSX1T
Vespa 200 Cosa VSR1T
Thickness: 2 mm, tempered material
Crimaz rear disc brake kit for Vespa Vespa 125 GT/GTR/TS/150 Sprint/V/GL/P150S /Rally/PX80-200/PE/Lusso/´98 /MY/´11/T5
Vespa 125 GT/GTR/Super/TS/150 GL/Sprint/V/Super/P150S/Rally/PX80-200/PE/Lusso/´98/MY/´11/T5
Primary transmission gear pinion 28 Teeth (28-69) for Vespa 50-90-125 Primavera/ET3/PK
Vespa 50 V5A1T N,L,R
Vespa 50 PK
Vespa 90 V9A1T
Vespa 125 Primavera VMA1>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Fits perfectly on bell 27-69, complete with washer and nut
Complete clutch Crimaz CMX Vespa 125/150/200 Sprint-S.Veloce-GT-GTR-TS-PX-PE
Vespa 125 VNB/GT/GTR/TS/PX
Vespa 150 VBB/GL/Sprint/Sprint Veloce/PX
Vespa 200 PE
The CMX is defined as a turned clutch because the basket is integral with the gear (pinion). This technical choice allows the basket (commonly known as the
bell) to remain stationary when the clutch is pulled (clutch disengagement).
Thanks to this reversal of moving parts, the clutch
becomes much more progressive in the initial thrust phase of the Vespa
minimizing any annoying jerks at start-up
(a problem known to old-design clutches). This precaution,
together with the significant contact points of the lined discs and conducting discs,
makes the CMX an ideal clutch for engines with power
greater than 15 hp, avoiding premature wear caused by the
hammering of the contact parts.
Vespa 125 VNB1T > VNB6T
Vespa 150 VBA1T
Vespa 150 VBB1T > VBB2T
Vespa 125 Super VNC1T
Vespa 125 GT VNL2T
Vespa 125 GTR VNL2T
Vespa 125 TS VNL3T
Vespa 125 PX
Vespa 150 PX
Vespa 150 Super VBC1T
Vespa 150 Sprint VLB1T
Vespa 150 Sprint Veloce VLB1T
Vespa 150 GL VLA1T
In laser-cut steel
Vespa 50 V5A1T N,L,R from 1966
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1>4T
Vespa 90 V9A1T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
In galvanized metal.
Vespa 50 V5A1T 92877>
Vespa 50 Special V5A2>3T
Vespa 50 Special V5B1T>3T
Vespa 50 PK
Vespa 90 V9A1T 25001>
Vespa 90 SS V9SS2T
Vespa 125 Primavera VMA1T>2T
Vespa 125 Primavera ET3 VMB1T
Vespa 125 PK
Silent Blocks specifically created to eliminate the elastic effect that we feel on traditional models, all supported by 2 bearings held in place by an acetal resin bushing.
The attachment to the frame is done with two M10 bolts.