Galvanized

Engage with original crowns

Cream-colored background, scaled at 90 KM/H

LED conversion kit for Vespa GTR, Rally, TS, and SV, including everything needed for the conversion to direct current of your electrical system, even with the original ignition.

Specifically, the following components are provided: -12 V DC voltage regulator specific for Vespa use; -Plug and play front bulb holder with dual filament bulb and position lamp; -Rear position lamp; -Brake indicator lamp.

The installation does not require any structural modifications to headlights or bodywork, nor does it involve replacing existing cables: the only interventions are made (if necessary) on the light switch and stop button and are completely reversible, allowing you to return your Vespa to its original state in the blink of an eye.
In addition to the supplied material, a small-sized battery is needed, which will be charged when the engine is running and will actively power the entire electrical system. The provided bulb holder, in addition to being perfectly compatible with the original fittings, has been designed and manufactured to achieve the best possible lamp-reflector alignment: this allows maximizing performance, as the projection of the light beam is directed exclusively onto a wide area of the ground with maximum
homogeneity.

Evening outings in the moon

Perfectly compatible with all models with a long splined lever, it increases the operating pressure by significantly "softening" the lever.

If you have a short lever available, proceed as follows:

Disassemble by removing the elastic pin, cut the lever in half with a hacksaw, then cut a 10/12mm sheet metal plate and weld it. You will then have a lever made up of 3 pieces longer than the original by about 10/12 mm.

Premium version, already cut to size

Full shoulders Ø88mm, stroke 54mm, connecting rod 105mm, shaft length 48mm.
Wrist pin 15 mm

flywheel side bearing seat diameter: 25mm
flywheel side oil seal seat diameter: 24mm

Hole center distance--> 61 mm

Kit composed of:

- Cable grommets and engine caps

- Grips

- Frame seals and bellows

- Stand feet

- Tank seals

Rubber quality guaranteed for most of the kit components by ARIETE (leader in the production of rubber parts for Vespa)

Material: Plastic

M14x1.25, wrench width 20.8mm
shielded/short thread
corresponds to BOSCH WR4AC/WR5AC/DENSO W22FSR/NGK BR7HS

1 green wire
hole distance 5.2 mm-hole distance 43 mm-12.5 mm

1 yellow wire, 1 blue wire
hole distance 5.2 mm-hole distance 43 mm-12.5 mm

Hole spacing: 34 mm

In black plastic

For points ignition systems

For proper functioning, it is necessary to equip with parachute pads

Lift the rear part of the vehicle by a few centimeters and it allows
to quickly change the rear wheel, the exhaust pipe, etc. The
vehicle remains firmly supported.

The 3x1 plate with phone holder, code G18BB1026, is designed to offer versatility and practicality to vintage Vespa owners. This universal accessory is compatible with all Vespa models, ensuring easy and secure installation thanks to its plug and play configuration.

280 mm
125 mm
Mounting bracket

The "1025 blue Edition" rearview mirror for vintage Vespa is an accessory that combines elegance and functionality for classic Vespa enthusiasts. With an exclusive design, this rearview mirror offers a touch of luxury and style to your vintage Vespa.

280 mm
125 mm
Mounting bracket

The "1025 Gold Edition" mirror for vintage Vespa is an accessory that combines elegance and functionality for classic Vespa enthusiasts. With an exclusive design, this mirror offers a touch of luxury and style to your vintage Vespa.

Approved E3

Universal Compatibility: Thanks to a patented strap and a clamp kit with diameters of 8, 10, 13, and 15 mm, the phone holder can be mounted on any rearview mirror rod.
Full Adjustability: The phone holder is fully adjustable, allowing it to fit different phone models and viewing angles.
Aluminum Construction: Made entirely of aluminum to ensure sturdiness and durability, while maintaining a sleek and refined look.
Vibration Reduction: Designed to keep the phone holder steady on the rearview mirror and dampen vibrations, ensuring stable viewing while driving.
Black Color: Finished in black for an elegant and discreet appearance that matches any motorcycle style.
The universal rod phone holder code 8094 is the perfect choice for those looking for a practical, safe, and stylish accessory. With its robust construction and advanced features, it offers a more comfortable and secure driving experience, keeping the phone always within reach.

a=13.3mm
key 12mm
steel, galvanized
10.9
black galvanized
5 pieces

Finish: Raw
To be welded to the frame
Replacement made in Italy

Premium quality

Attention: The plastic skirt is not included

Note: The plastic skirt is not included

Kit composed of:

• Glass
• Chrome frame
• Seal

Purely illustrative photo For models with arrows, electronic ignition and electric starter
For models with arrows, electronic ignition and electric starter

H-->320 mm

Note--> Lower the thickness to 6 mm.

Steel
Chrome-plated
With decorative pattern